Datasheet Texas Instruments TPS61132PW — Ficha de datos
| Fabricante | Texas Instruments |
| Serie | TPS61132 |
| Numero de parte | TPS61132PW |
Convertidor SEPIC de 3,3 V, 90% de eficiencia con LDO de 1,5 V, 200 mA para aplicaciones de LiIon de 1 celda o de doble celda 16-TSSOP -40 a 85
Hojas de datos
TPS6113x Synchronous SEPIC and Flyback Converter With 1.1-A Switch and Integrated LDO datasheet
PDF, 1.2 Mb, Revisión: C, Archivo publicado: sept 29, 2015
Extracto del documento
Precios
Estado
| Estado del ciclo de vida | Activo (Recomendado para nuevos diseños) |
| Disponibilidad de muestra del fabricante | Sí |
Embalaje
| Pin | 16 |
| Package Type | PW |
| Industry STD Term | TSSOP |
| JEDEC Code | R-PDSO-G |
| Package QTY | 90 |
| Carrier | TUBE |
| Device Marking | PS61132 |
| Width (mm) | 4.4 |
| Length (mm) | 5 |
| Thickness (mm) | 1 |
| Pitch (mm) | .65 |
| Max Height (mm) | 1.2 |
| Mechanical Data | Descargar |
Paramétricos
| Duty Cycle(Max) | 100 % |
| Iq(Typ) | 0.04 mA |
| Operating Temperature Range | -40 to 85 C |
| Package Group | TSSOP |
| Rating | Catalog |
| Regulated Outputs | 2 |
| Special Features | Enable,Light Load Efficiency,Load Disconnect,Power Good |
| Switch Current Limit(Min) | 1.1 A |
| Switch Current Limit(Typ) | 1.3 A |
| Switching Frequency(Max) | 600 kHz |
| Switching Frequency(Min) | 400 kHz |
| Type | Converter |
| Vin(Max) | 5.5 V |
| Vin(Min) | 1.8 V |
| Vout(Max) | 3.3 V |
| Vout(Min) | 3.3 V |
Plan ecológico
| RoHS | Obediente |
Notas de aplicación
- Minimizing Ringing at the Switch Node of a Boost ConverterPDF, 201 Kb, Archivo publicado: sept 15, 2006
The application report explains how to use proper board layout and/or a snubber to reduce high-frequency ringing at the switch node of a boost converter. - Optimizing Resistor Dividers at a Comparator (Rev. A)PDF, 120 Kb, Revisión: A, Archivo publicado: jun 3, 2013
- Basic Calculation of a Boost Converter's Power Stage (Rev. C)PDF, 186 Kb, Revisión: C, Archivo publicado: enero 8, 2014
This application note gives the equations to calculate the power stage of a boost converter built with an IC with integrated switch and operating in continuous conduction mode. It is not intended to give details on the functionality of a boost converter (see Reference 1) or how to compensate a converter. See the references at the end of this document if more detail is needed. - Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. A)PDF, 1.1 Mb, Revisión: A, Archivo publicado: mayo 11, 2015
- Extending the Soft Start Time Without a Soft Start Pin (Rev. B)PDF, 387 Kb, Revisión: B, Archivo publicado: jun 15, 2017
- Choosing an Appropriate Pull-up/Pull-down Resistor for Open Drain OutputsPDF, 130 Kb, Archivo publicado: sept 19, 2011
- QFN and SON PCB Attachment (Rev. B)PDF, 821 Kb, Revisión: B, Archivo publicado: agosto 24, 2018
- IQ: What it is what it isn’t and how to use itPDF, 198 Kb, Archivo publicado: jun 17, 2011
- Performing Accurate PFM Mode Efficiency Measurements (Rev. A)PDF, 418 Kb, Revisión: A, Archivo publicado: dic 11, 2018
When performing measurements on DC-DC converters using pulse frequency modulation(PFM)or any power save mode proper care must be taken to ensure that the measurements are accurate. An accurate PFM mode efficiency measurement is critical for systems which require high efficiency at low loads such as in smart home systems tablets wearables and metering.
Linea modelo
Serie: TPS61132 (2)
- TPS61132PW TPS61132PWRG4
Clasificación del fabricante
- Semiconductors > Power Management > Non-isolated DC/DC Switching Regulator > Step-Up (Boost) > Boost Converter (Integrated Switch)