Datasheet Analog Devices OP400EY — Ficha de datos

REVISIONS
LTR DATE (YR-MO-DA) APPROVED A Change to one part-one number format. Add table III. Editorial changes
throughout. DESCRIPTION 91-12-11 M. A. FRYE B Make changes to Slew rate test as specified under Table I.
Changes in accordance with NOR 5962-R049-95. 94-12-21 M. A. FRYE 96-11-26 R. MONNIN Add case outline K. Table I, slew rate test, in the conditions column delete
“VIN = ±5.0 V” and “measured at VOUT = ±2.5 V”. Table IIA, group C end-point
parameters; for device class V add “1,2,3,4,5,6,7,8 2/”.
Changes in accordance with NOR 5962-R035-97. C D Removed table III, burn-in, dynamic burn-in, static and dynamic test circuits.
Drawing updated to reflect current requirements. -rrp 02-12-17 R. MONNIN E Update boilerplate paragraphs to current MIL-PRF-38535 requirements. -rrp 10-03-02 C. SAFFLE F Deleted appendix A. Added paragraph 6.7 PIN supersession information.
Update drawing to current MIL-PRF-38535 requirements. -rrp 16-12-19 C. SAFFLE G Add radiation hardened requirements for device type 01. -ro 17-03-24 C. SAFFLE REV
SHEET
REV
SHEET
REV STATUS REV G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY
MARCIA B. KELLEHER STANDARD
MICROCIRCUIT
DRAWING DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil CHECKED BY
D. A. DiCENZO
APPROVED BY THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE …

Quad Low Offset, Low Power
Operational Amplifier
OP400 Data Sheet FUNCTIONAL BLOCK DIAGRAMS
OUTA 1
OUT A 1
–IN A 2 – + – + +IN A 3
V+ 4 OP400 +IN B 5
–IN B 6
OUT B 7 – + + – 14 OUT D –IN A 2 13 –IN D +IN A 3 12 +IN D V+ 4 The OP400 is the first monolithic quad operational amplifier
that features OP77-type performance. Precision performance is
not sacrificed with the OP400 to obtain the space and cost savings
offered by quad amplifiers.
The OP400 features an extremely low input offset voltage of less
than 150 μV with a drift of less than 1.2 μV/°C, guaranteed over
the full military temperature range. Open-loop gain of the OP400
is more than 5 million into a 10 kΩ load, input bias current is
less than 3 nA, common-mode rejection (CMR) is more than
120 dB, and power supply rejection ratio (PSRR) is less than
1.8 μV/V. On-chip Zener zap trimming achieves the low input
offset voltage of the OP400 and eliminates the need for offset + + – OP400 16 OUT D 15 –IN D 14 +IN D 13 V– 12 +IN C 11 –IN C +IN B 5 10 +IN C –IN B 6 9 –IN C OUT B 7 10 OUT C 8 OUT C NC 8 9 NC – + + – NC = NO CONNECT Figure 1. 14-Lead Ceramic Dual In-Line
Package [CERDIP] and 14-Lead Plastic
Dual In-Line Package [PDIP] GENERAL DESCRIPTION – 11 V– 00304-001 Low input offset voltage: 150 μV (maximum)
Low offset voltage drift over –55°C to +125°C: 1.2 μV/°C …

Quad Low Offset, Low Power
Operational Amplifier
OP400 Data Sheet FUNCTIONAL BLOCK DIAGRAMS
OUTA 1
OUT A 1
–IN A 2 – + – + +IN A 3
V+ 4 OP400 +IN B 5
–IN B 6 – + + – OUT B 7 14 OUT D –IN A 2 13 –IN D +IN A 3 12 +IN D V+ 4 11 V– 10 +IN C –IN B 6 9 –IN C OUT B 7 8 OUT C 16 OUT D
– + + – NC 8 15 –IN D
14 +IN D
13 V– OP400 +IN B 5 00304-001 Low input offset voltage: 150 µV maximum
Low offset voltage drift over –55°C to +125°C: 1.2 μV/°C
maximum
Low supply current (per amplifier): 725 µA maximum
High open-loop gain: 5000 V/mV minimum
Input bias current: 3 nA maximum
Low noise voltage density: 11 nV/√Hz at 1 kHz
Stable with large capacitive loads: 10 nF typical
Available in die form 12 +IN C
– + + – 11 –IN C
10 OUT C
9 NC NC = NO CONNECT Figure 1. 14-Pin Ceramic DIP (Y-Suffix)
and 14-Pin Plastic DIP (P-Suffix) 00304-002 FEATURES Figure 2. 16-Pin SOIC (S-Suffix) GENERAL DESCRIPTION …