Datasheet Texas Instruments LM3488MMX — Ficha de datos

FabricanteTexas Instruments
SerieLM3488
Numero de parteLM3488MMX
Datasheet Texas Instruments LM3488MMX

Controlador de canal N de 40V de ancho bajo y bajo canal para reguladores de conmutación 8-VSSOP -40 a 125

Hojas de datos

LM3488/-Q1 Automotive High-Efficiency Controller for Boost, SEPIC and Fly-Back DC-DC Converters datasheet
PDF, 1.7 Mb, Revisión: O, Archivo publicado: jul 6, 2015
Extracto del documento

Precios

Estado

Estado del ciclo de vidaNRND (No recomendado para nuevos diseños)
Disponibilidad de muestra del fabricanteNo

Embalaje

Pin8
Package TypeDGK
Industry STD TermVSSOP
JEDEC CodeR-PDSO-G
Device MarkingS21B
Width (mm)3
Length (mm)3
Thickness (mm).97
Pitch (mm).65
Max Height (mm)1.07
Mechanical DataDescargar

Reemplazos

ReplacementLM3488MMX/NOPB
Replacement CodeS

Paramétricos

Approx. Price (US$)0.80 | 1ku
Duty Cycle(Max)(%)100
Iout(Max)(A)10
Iq(Typ)(mA)2.7
Operating Temperature Range(C)-40 to 125
Package GroupVSSOP
RatingCatalog
Regulated Outputs(#)1
Special FeaturesAdjustable Current Limit
Enable
Frequency Synchronization
Light Load Efficiency
Pre-Bias Start-Up
Switch Current Limit(Typ)(A)10
Switching Frequency(Max)(kHz)1000
Switching Frequency(Min)(kHz)100
TypeController
Vin(Max)(V)40
Vin(Min)(V)2.97
Vout(Max)(V)500
Vout(Min)(V)1.26

Plan ecológico

RoHSDesobediente
Pb gratisNo

Notas de aplicación

  • LM34xx How to Design Flyback Converter with LM3481 Boost Controller
    PDF, 1.7 Mb, Archivo publicado: sept 21, 2016
    The TexasInstrumentsLM3481boostcontrolleris a versatilelow-sideN-FEThigh-performancecontrollerfor switchingregulators.Thedevicehaswiderangeof applicationssuchas automotivestart-stopapplication,one-cellor two-cellLi-ionbattery-poweredportableBluetoothaudiosystem,industrialsystemisolatedsupplies,and so forth,and supportstopologi
  • AN-1286 Compensation For The LM3478 Boost Controller (Rev. C)
    PDF, 356 Kb, Revisión: C, Archivo publicado: abr 23, 2013
    The LM3478 is a low side N-Channel controller for switching regulators. Like many switching controllers,the added flexibility in component selection can cause problems for users when determining thecompensation scheme. It is the goal of this application report to present a decent groundwork to allow thereader to select with confidence the correct compensation components. To achieve this we l
  • AN-1484 Designing A SEPIC Converter (Rev. E)
    PDF, 220 Kb, Revisión: E, Archivo publicado: abr 23, 2013
    In a single ended primary inductance converter (SEPIC) design, the output voltage can be higher or lowerthan the input voltage. The SEPIC converter shown in Figure 1 uses two inductors: L1 and L2. The twoinductors can be wound on the same core since the same voltages are applied to them throughout theswitching cycle.
  • Modeling & Design of Current Mode Control Boost Converters (Rev. B)
    PDF, 316 Kb, Revisión: B, Archivo publicado: abr 23, 2013
    This application note presents a detail modeling and design of current mode control boost convertersoperating in the continuous conduction mode (CCM). Based on the derived small signal models, thedesign of a lag compensator for current mode control boost converters will be detailed. The LM3478 boostcontroller will be used in the example. Simulation and hardware measurement of frequency respo
  • AN-1990 Compensation for Current Mode Control SEPIC Converters (Rev. A)
    PDF, 247 Kb, Revisión: A, Archivo publicado: abr 23, 2013
    This application note discusses the use of SEPIC converters in various applications.

Linea modelo

Clasificación del fabricante

  • Semiconductors > Power Management > Non-isolated DC/DC Switching Regulator > Step-Up (Boost) > Boost Controller (External Switch)