Datasheet Texas Instruments LM2590HVT-ADJ/NOPB — Ficha de datos

FabricanteTexas Instruments
SerieLM2590HV
Numero de parteLM2590HVT-ADJ/NOPB
Datasheet Texas Instruments LM2590HVT-ADJ/NOPB

INTERRUPTOR SIMPLE Convertidor de potencia 150 KHz 1A Regulador de voltaje reductor con características 7-TO-220 -40 a 125

Hojas de datos

LM2590HV SIMPLE SWITCHERВ® Power Converter 150-kHz, 1-A Step-Down Voltage Regulator datasheet
PDF, 1.7 Mb, Revisión: C, Archivo publicado: jul 28, 2016
Extracto del documento

Precios

Estado

Estado del ciclo de vidaActivo (Recomendado para nuevos diseños)
Disponibilidad de muestra del fabricante

Embalaje

Pin77
Package TypeNDZNDZ
Industry STD TermTO-220TO-220
JEDEC CodeR-MSFM-LR-MSFM-L
Package QTY4545
CarrierTUBETUBE
Device Marking-ADJ P+LM2590HVT
Width (mm)10.1610.16
Length (mm)14.98614.986
Thickness (mm)4.5724.572
Pitch (mm)1.271.27
Max Height (mm)4.74.7
Mechanical DataDescargarDescargar

Paramétricos

Control ModeVoltage Mode
Duty Cycle(Max)100 %
Iout(Max)1 A
Iq(Typ)5 mA
Operating Temperature Range-40 to 125 C
Package GroupTO-220
RatingCatalog
Regulated Outputs1
Special FeaturesPower Good
Switching Frequency(Max)173 kHz
Switching Frequency(Min)110 kHz
TypeConverter
Vin(Max)60 V
Vin(Min)4.5 V
Vout(Max)57 V
Vout(Min)3.3 V

Plan ecológico

RoHSObediente

Notas de aplicación

  • AN-643 EMI/RFI Board Design (Rev. B)
    PDF, 742 Kb, Revisión: B, Archivo publicado: mayo 3, 2004
    Application Note 643 EMI/RFI Board Design
  • Cost-Effective Transformerless Offline Supply for Light Load Applications (Rev. A)
    PDF, 295 Kb, Revisión: A, Archivo publicado: jun 16, 2015
    This design idea provides a simple non-isolated AC/DC power supply for low power applications. Thedesign uses a "capacitive-dropper" front-end combined with a LM46000 SIMPLE SWITCHERВ® buckregulator from Texas Instruments. The circuit provides 3.3 V at a minimum of 100 mA from a line supply of90 VAC to 265 VAC. Theory of operation as well as design equations and performance results are given.
  • Input and Output Capacitor Selection
    PDF, 219 Kb, Archivo publicado: sept 19, 2005
  • AN-1197 Selecting Inductors for Buck Converters (Rev. B)
    PDF, 558 Kb, Revisión: B, Archivo publicado: abr 23, 2013
    This application report provides design information to help select an off-the-shelf inductor for anycontinuous-mode buck converter application.
  • AN-2155 Layout Tips for EMI Reduction in DC/ DC Converters (Rev. A)
    PDF, 3.6 Mb, Revisión: A, Archivo publicado: abr 23, 2013
    This application note will explore how the layout of your DC/DC power supply can significantly affect theamount of EMI that it produces. It will discuss several variations of a layout analyze the results andprovide answers to some common EMI questions such whether or not to use a shielded inductor.
  • AN-1566 Techniques for Thermal Analysis of Switching Power Supply Designs (Rev. A)
    PDF, 1.4 Mb, Revisión: A, Archivo publicado: abr 23, 2013
    This application note provides thermal power analysis techniques for analyzing the power IC.
  • AN-1889 How to Measure the Loop Transfer Function of Power Supplies (Rev. A)
    PDF, 2.7 Mb, Revisión: A, Archivo publicado: abr 23, 2013
    This application report shows how to measure the critical points of a bode plot with only an audiogenerator (or simple signal generator) and an oscilloscope. The method is explained in an easy to followstep-by-step manner so that a power supply designer can start performing these measurements in a shortamount of time.
  • Semiconductor and IC Package Thermal Metrics (Rev. C)
    PDF, 201 Kb, Revisión: C, Archivo publicado: abr 19, 2016
  • Cap Drop Offline Supply for E-Meters
    PDF, 291 Kb, Archivo publicado: jun 16, 2015
    This design idea provides a simple non-isolated AC/DC power supply for low power applications such assmart grid E-meter applications. The design uses a "capacitive-dropper" front-end combined with aLM46000 SIMPLE SWITCHERВ® buck regulator from Texas Instruments. The circuit provides 3.3 V at aminimum of 50 mA from a line supply of 90 VAC to 265 VAC. Theory of operation as well as designequa
  • Low EMI Layout Made SIMPLE With LM43600/1/2/3 and LM46000/1/2 (Rev. A)
    PDF, 512 Kb, Revisión: A, Archivo publicado: sept 12, 2014
    Printed Circuit Board (PCB) layout for Switched Mode Power Supplies (SMPS) is critical to achieve proper converter operation good thermal performance and excellent radiated EMI performance. Optimized board layout for low radiated EMI is made very simple by the package and pin arrangement of the SIMPLE SWITCHER Synchronous Buck Converter family LM4360x and LM4600x
  • Simple Techniques Minimize Cross-Coupling in Distributed Power Systems
    PDF, 335 Kb, Archivo publicado: marzo 21, 2007
  • AN-1149 Layout Guidelines for Switching Power Supplies (Rev. C)
    PDF, 82 Kb, Revisión: C, Archivo publicado: abr 23, 2013
    When designing a high frequency switching regulated power supply layout is very important. Using agood layout can solve many problems associated with these types of supplies. The problems due to a badlayout are often seen at high current levels and are usually more obvious at large input to output voltagedifferentials. Some of the main problems are loss of regulation at high output current
  • AN-1081 Low-Cost Low-Parts-Count DC/DC Converter With Multiple Outputs (Rev. B)
    PDF, 124 Kb, Revisión: B, Archivo publicado: abr 23, 2013
    This application report describes a simple low cost, low parts-count multiple output DC/DC converterbased on the LM2596 five terminal step-down switching regulator. The circuit described provides multipleoutput voltages (positive and negative) with good regulation using a step-down converter circuit withflyback windings. It uses only one switching regulator IC.
  • AN-1229 SIMPLE SWITCHER PCB Layout Guidelines (Rev. C)
    PDF, 374 Kb, Revisión: C, Archivo publicado: abr 23, 2013
    This application report provides SIMPLE SWITCHER™ PCB layout guidelines.
  • AN-2162 Simple Success With Conducted EMI From DC-DC Converters (Rev. C)
    PDF, 2.5 Mb, Revisión: C, Archivo publicado: abr 24, 2013
    Electromagnetic Interference (EMI) is an unwanted effect between two electrical systems as a result ofeither electromagnetic radiation or electromagnetic conduction. EMI is the major adverse effect caused bythe application of switch-mode power supplies (SMPS). In switching power supplies EMI noise isunavoidable due to the switching actions of the semiconductor devices and resulting disconti
  • AN-1246 Stresses in Wide Input DC-DC Converters (Rev. C)
    PDF, 427 Kb, Revisión: C, Archivo publicado: abr 23, 2013
    This application note discusses stresses in wide input DC-DC converters.
  • AN-1520 A Guide to Board Layout for Best Thermal Resistance for Exposed Packages (Rev. B)
    PDF, 9.2 Mb, Revisión: B, Archivo publicado: abr 23, 2013
    This thermal application report provides guidelines for the optimal board layout to achieve the best thermalresistance for exposed packages. The thermal resistance between junction-to-ambient (ОёJA) is highlydependent on the PCB (Printed Circuit Board) design factors. This becomes more critical for packageshaving very low thermal resistance between junction-to-case such as exposed pad TSSOP

Linea modelo

Clasificación del fabricante

  • Semiconductors > Power Management > Non-isolated DC/DC Switching Regulator > Step-Down (Buck) > Buck Converter (Integrated Switch)

Otros nombres:

LM2590HVTADJ/NOPB, LM2590HVT ADJ/NOPB