Datasheet Texas Instruments TPS61010DGS — Ficha de datos

FabricanteTexas Instruments
SerieTPS61010
Numero de parteTPS61010DGS
Datasheet Texas Instruments TPS61010DGS

Convertidor Boost síncrono de bajo voltaje de entrada con salida ajustable 10-VSSOP -40 a 85

Hojas de datos

TPS6101x High-Efficiency, 1-Cell and 2-Cell Boost Converters datasheet
PDF, 1.1 Mb, Revisión: F, Archivo publicado: agosto 4, 2015
Extracto del documento

Precios

Estado

Estado del ciclo de vidaActivo (Recomendado para nuevos diseños)
Disponibilidad de muestra del fabricante

Embalaje

Pin10
Package TypeDGS
Industry STD TermVSSOP
JEDEC CodeS-PDSO-G
Package QTY80
CarrierTUBE
Device MarkingAIP
Width (mm)3
Length (mm)3
Thickness (mm)1.02
Pitch (mm).5
Max Height (mm)1.07
Mechanical DataDescargar

Paramétricos

Duty Cycle(Max)100 %
Iq(Typ)0.05 mA
Operating Temperature Range-40 to 85 C
Package GroupVSSOP
RatingCatalog
Regulated Outputs1
Special FeaturesEnable,Light Load Efficiency,Output Discharge,Power Good
Switch Current Limit(Min)1.07 A
Switch Current Limit(Typ)1.13 A
Switching Frequency(Max)780 kHz
Switching Frequency(Min)420 kHz
TypeConverter
Vin(Max)3.3 V
Vin(Min)0.8 V
Vout(Max)3.3 V
Vout(Min)1.5 V

Plan ecológico

RoHSObediente

Kits de diseño y Módulos de evaluación

  • Evaluation Modules & Boards: TPS61016EVM-157
    Fixed 3.3-V High-Efficiency Boost Converter
    Estado del ciclo de vida: Activo (Recomendado para nuevos diseños)
  • Evaluation Modules & Boards: TPS61015EVM-157
    Fixed 3.0-V High-Efficiency Boost Converter
    Estado del ciclo de vida: Activo (Recomendado para nuevos diseños)

Notas de aplicación

  • Factors That Determine Light Load PSM Switching Frequncy for TPS6101X Boost Conv
    PDF, 183 Kb, Archivo publicado: dic 6, 2006
    This application report explains the factors that determine the low output power switching frequencies when using the TPS6101x step-up converters.
  • Minimizing Ringing at the Switch Node of a Boost Converter
    PDF, 201 Kb, Archivo publicado: sept 15, 2006
    The application report explains how to use proper board layout and/or a snubber to reduce high-frequency ringing at the switch node of a boost converter.
  • Design considerations for a resistive feedback divider in a DC/DC converter
    PDF, 393 Kb, Archivo publicado: abr 26, 2012
  • Basic Calculation of a Boost Converter's Power Stage (Rev. C)
    PDF, 186 Kb, Revisión: C, Archivo publicado: enero 8, 2014
    This application note gives the equations to calculate the power stage of a boost converter built with an IC with integrated switch and operating in continuous conduction mode. It is not intended to give details on the functionality of a boost converter (see Reference 1) or how to compensate a converter. See the references at the end of this document if more detail is needed.
  • Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. A)
    PDF, 1.1 Mb, Revisión: A, Archivo publicado: mayo 11, 2015
  • Extending the Soft Start Time Without a Soft Start Pin (Rev. B)
    PDF, 387 Kb, Revisión: B, Archivo publicado: jun 15, 2017
  • Choosing an Appropriate Pull-up/Pull-down Resistor for Open Drain Outputs
    PDF, 130 Kb, Archivo publicado: sept 19, 2011
  • IQ: What it is what it isn’t and how to use it
    PDF, 198 Kb, Archivo publicado: jun 17, 2011
  • Performing Accurate PFM Mode Efficiency Measurements (Rev. A)
    PDF, 418 Kb, Revisión: A, Archivo publicado: dic 11, 2018
    When performing measurements on DC-DC converters using pulse frequency modulation(PFM)or any power save mode proper care must be taken to ensure that the measurements are accurate. An accurate PFM mode efficiency measurement is critical for systems which require high efficiency at low loads such as in smart home systems tablets wearables and metering.

Linea modelo

Serie: TPS61010 (4)

Clasificación del fabricante

  • Semiconductors > Power Management > Non-isolated DC/DC Switching Regulator > Step-Up (Boost) > Boost Converter (Integrated Switch)