Datasheet Texas Instruments TPS61010DGSG4 — Ficha de datos
Fabricante | Texas Instruments |
Serie | TPS61010 |
Numero de parte | TPS61010DGSG4 |
Convertidor Boost síncrono de bajo voltaje de entrada con salida ajustable 10-VSSOP -40 a 85
Hojas de datos
TPS6101x High-Efficiency, 1-Cell and 2-Cell Boost Converters datasheet
PDF, 1.1 Mb, Revisión: F, Archivo publicado: agosto 4, 2015
Extracto del documento
Precios
Estado
Estado del ciclo de vida | Activo (Recomendado para nuevos diseños) |
Disponibilidad de muestra del fabricante | Sí |
Embalaje
Pin | 10 |
Package Type | DGS |
Industry STD Term | VSSOP |
JEDEC Code | S-PDSO-G |
Package QTY | 80 |
Carrier | TUBE |
Device Marking | AIP |
Width (mm) | 3 |
Length (mm) | 3 |
Thickness (mm) | 1.02 |
Pitch (mm) | .5 |
Max Height (mm) | 1.07 |
Mechanical Data | Descargar |
Paramétricos
Duty Cycle(Max) | 100 % |
Iq(Typ) | 0.05 mA |
Operating Temperature Range | -40 to 85 C |
Package Group | VSSOP |
Rating | Catalog |
Regulated Outputs | 1 |
Special Features | Enable,Light Load Efficiency,Output Discharge,Power Good |
Switch Current Limit(Min) | 1.07 A |
Switch Current Limit(Typ) | 1.13 A |
Switching Frequency(Max) | 780 kHz |
Switching Frequency(Min) | 420 kHz |
Type | Converter |
Vin(Max) | 3.3 V |
Vin(Min) | 0.8 V |
Vout(Max) | 3.3 V |
Vout(Min) | 1.5 V |
Plan ecológico
RoHS | Obediente |
Kits de diseño y Módulos de evaluación
- Evaluation Modules & Boards: TPS61016EVM-157
Fixed 3.3-V High-Efficiency Boost Converter
Estado del ciclo de vida: Activo (Recomendado para nuevos diseños) - Evaluation Modules & Boards: TPS61015EVM-157
Fixed 3.0-V High-Efficiency Boost Converter
Estado del ciclo de vida: Activo (Recomendado para nuevos diseños)
Notas de aplicación
- Factors That Determine Light Load PSM Switching Frequncy for TPS6101X Boost ConvPDF, 183 Kb, Archivo publicado: dic 6, 2006
This application report explains the factors that determine the low output power switching frequencies when using the TPS6101x step-up converters. - Minimizing Ringing at the Switch Node of a Boost ConverterPDF, 201 Kb, Archivo publicado: sept 15, 2006
The application report explains how to use proper board layout and/or a snubber to reduce high-frequency ringing at the switch node of a boost converter. - Design considerations for a resistive feedback divider in a DC/DC converterPDF, 393 Kb, Archivo publicado: abr 26, 2012
- Basic Calculation of a Boost Converter's Power Stage (Rev. C)PDF, 186 Kb, Revisión: C, Archivo publicado: enero 8, 2014
This application note gives the equations to calculate the power stage of a boost converter built with an IC with integrated switch and operating in continuous conduction mode. It is not intended to give details on the functionality of a boost converter (see Reference 1) or how to compensate a converter. See the references at the end of this document if more detail is needed. - Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. A)PDF, 1.1 Mb, Revisión: A, Archivo publicado: mayo 11, 2015
- Extending the Soft Start Time Without a Soft Start Pin (Rev. B)PDF, 387 Kb, Revisión: B, Archivo publicado: jun 15, 2017
- Choosing an Appropriate Pull-up/Pull-down Resistor for Open Drain OutputsPDF, 130 Kb, Archivo publicado: sept 19, 2011
- IQ: What it is what it isn’t and how to use itPDF, 198 Kb, Archivo publicado: jun 17, 2011
- Performing Accurate PFM Mode Efficiency Measurements (Rev. A)PDF, 418 Kb, Revisión: A, Archivo publicado: dic 11, 2018
When performing measurements on DC-DC converters using pulse frequency modulation(PFM)or any power save mode proper care must be taken to ensure that the measurements are accurate. An accurate PFM mode efficiency measurement is critical for systems which require high efficiency at low loads such as in smart home systems tablets wearables and metering.
Linea modelo
Serie: TPS61010 (4)
- TPS61010DGS TPS61010DGSG4 TPS61010DGSR TPS61010DGSRG4
Clasificación del fabricante
- Semiconductors > Power Management > Non-isolated DC/DC Switching Regulator > Step-Up (Boost) > Boost Converter (Integrated Switch)