Datasheet Texas Instruments LMR12020 — Ficha de datos

FabricanteTexas Instruments
SerieLMR12020
Datasheet Texas Instruments LMR12020

INTERRUPTOR SIMPLE 3V a 20V, Regulador de conmutación CC / CC reductor 2.0A 2.0A en LLP-10

Hojas de datos

SIMPLE SWITCHER® 20Vin, 2.0A Step-Down Voltage Regul datasheet
PDF, 1.4 Mb, Revisión: A, Archivo publicado: marzo 22, 2013
Extracto del documento

Precios

Estado

LMR12020XSD/NOPBLMR12020XSDX/NOPB
Estado del ciclo de vidaActivo (Recomendado para nuevos diseños)Activo (Recomendado para nuevos diseños)
Disponibilidad de muestra del fabricanteNo

Embalaje

LMR12020XSD/NOPBLMR12020XSDX/NOPB
N12
Pin1010
Package TypeDSCDSC
Industry STD TermWSONWSON
JEDEC CodeS-PDSO-NS-PDSO-N
Package QTY10004500
CarrierSMALL T&RLARGE T&R
Device MarkingL284BL284B
Width (mm)33
Length (mm)33
Thickness (mm).75.75
Pitch (mm).5.5
Max Height (mm).8.8
Mechanical DataDescargarDescargar

Paramétricos

Parameters / ModelsLMR12020XSD/NOPB
LMR12020XSD/NOPB
LMR12020XSDX/NOPB
LMR12020XSDX/NOPB
Control ModeCurrent ModeCurrent Mode
Duty Cycle(Max), %9090
Iout(Max), A22
Iq(Typ), mA2.42.4
Operating Temperature Range, C-40 to 125-40 to 125
Package GroupWSONWSON
RatingCatalogCatalog
Regulated Outputs11
Special FeaturesEnable,Frequency SynchronizationEnable,Frequency Synchronization
Switching Frequency(Max), kHz23002300
Switching Frequency(Min), kHz10001000
TypeConverterConverter
Vin(Max), V2020
Vin(Min), V33
Vout(Max), V1818
Vout(Min), V11

Plan ecológico

LMR12020XSD/NOPBLMR12020XSDX/NOPB
RoHSObedienteObediente

Notas de aplicación

  • AN-643 EMI/RFI Board Design (Rev. B)
    PDF, 742 Kb, Revisión: B, Archivo publicado: mayo 3, 2004
    Application Note 643 EMI/RFI Board Design
  • Input and Output Capacitor Selection
    PDF, 219 Kb, Archivo publicado: sept 19, 2005
  • AN-1197 Selecting Inductors for Buck Converters (Rev. B)
    PDF, 558 Kb, Revisión: B, Archivo publicado: abr 23, 2013
    This application report provides design information to help select an off-the-shelf inductor for anycontinuous-mode buck converter application.
  • AN-2155 Layout Tips for EMI Reduction in DC/ DC Converters (Rev. A)
    PDF, 3.6 Mb, Revisión: A, Archivo publicado: abr 23, 2013
    This application note will explore how the layout of your DC/DC power supply can significantly affect theamount of EMI that it produces. It will discuss several variations of a layout analyze the results andprovide answers to some common EMI questions such whether or not to use a shielded inductor.
  • AN-1566 Techniques for Thermal Analysis of Switching Power Supply Designs (Rev. A)
    PDF, 1.4 Mb, Revisión: A, Archivo publicado: abr 23, 2013
    This application note provides thermal power analysis techniques for analyzing the power IC.
  • AN-1889 How to Measure the Loop Transfer Function of Power Supplies (Rev. A)
    PDF, 2.7 Mb, Revisión: A, Archivo publicado: abr 23, 2013
    This application report shows how to measure the critical points of a bode plot with only an audiogenerator (or simple signal generator) and an oscilloscope. The method is explained in an easy to followstep-by-step manner so that a power supply designer can start performing these measurements in a shortamount of time.
  • Semiconductor and IC Package Thermal Metrics (Rev. C)
    PDF, 201 Kb, Revisión: C, Archivo publicado: abr 19, 2016
  • AN-1149 Layout Guidelines for Switching Power Supplies (Rev. C)
    PDF, 82 Kb, Revisión: C, Archivo publicado: abr 23, 2013
    When designing a high frequency switching regulated power supply layout is very important. Using agood layout can solve many problems associated with these types of supplies. The problems due to a badlayout are often seen at high current levels and are usually more obvious at large input to output voltagedifferentials. Some of the main problems are loss of regulation at high output current
  • AN-1229 SIMPLE SWITCHER PCB Layout Guidelines (Rev. C)
    PDF, 374 Kb, Revisión: C, Archivo publicado: abr 23, 2013
    This application report provides SIMPLE SWITCHER™ PCB layout guidelines.
  • AN-2162 Simple Success With Conducted EMI From DC-DC Converters (Rev. C)
    PDF, 2.5 Mb, Revisión: C, Archivo publicado: abr 24, 2013
    Electromagnetic Interference (EMI) is an unwanted effect between two electrical systems as a result ofeither electromagnetic radiation or electromagnetic conduction. EMI is the major adverse effect caused bythe application of switch-mode power supplies (SMPS). In switching power supplies EMI noise isunavoidable due to the switching actions of the semiconductor devices and resulting disconti
  • AN-1246 Stresses in Wide Input DC-DC Converters (Rev. C)
    PDF, 427 Kb, Revisión: C, Archivo publicado: abr 23, 2013
    This application note discusses stresses in wide input DC-DC converters.
  • AN-1520 A Guide to Board Layout for Best Thermal Resistance for Exposed Packages (Rev. B)
    PDF, 9.2 Mb, Revisión: B, Archivo publicado: abr 23, 2013
    This thermal application report provides guidelines for the optimal board layout to achieve the best thermalresistance for exposed packages. The thermal resistance between junction-to-ambient (ОёJA) is highlydependent on the PCB (Printed Circuit Board) design factors. This becomes more critical for packageshaving very low thermal resistance between junction-to-case such as exposed pad TSSOP

Linea modelo

Clasificación del fabricante

  • Semiconductors> Power Management> Non-isolated DC/DC Switching Regulator> Step-Down (Buck)> Buck Converter (Integrated Switch)