Datasheet Texas Instruments LMR16006 — Ficha de datos

FabricanteTexas Instruments
SerieLMR16006
Datasheet Texas Instruments LMR16006

SWITCHER® SIMPLE 4V a 60V, regulador reductor de 600mA con bajo coeficiente intelectual

Hojas de datos

LMR16006 SIMPLE SWITCHER 60 V 0.6 A Buck Regulators With High Efficiency ECO Mode datasheet
PDF, 1.2 Mb, Archivo publicado: nov 20, 2013
Extracto del documento

Precios

Estado

LMR16006XDDCRLMR16006XDDCTLMR16006YDDCRLMR16006YDDCT
Estado del ciclo de vidaActivo (Recomendado para nuevos diseños)Activo (Recomendado para nuevos diseños)Activo (Recomendado para nuevos diseños)Activo (Recomendado para nuevos diseños)
Disponibilidad de muestra del fabricante

Embalaje

LMR16006XDDCRLMR16006XDDCTLMR16006YDDCRLMR16006YDDCT
N1234
Pin6666
Package TypeDDCDDCDDCDDC
Industry STD TermSOT-23-THINSOT-23-THINSOT-23-THINSOT-23-THIN
JEDEC CodeR-PDSO-GR-PDSO-GR-PDSO-GR-PDSO-G
Package QTY30002503000250
CarrierLARGE T&RSMALL T&RLARGE T&RSMALL T&R
Device MarkingD02XD02XD02YD02Y
Width (mm)1.61.61.61.6
Length (mm)2.92.92.92.9
Thickness (mm).87.87.87.87
Pitch (mm).95.95.95.95
Max Height (mm)1.11.11.11.1
Mechanical DataDescargarDescargarDescargarDescargar

Paramétricos

Parameters / ModelsLMR16006XDDCR
LMR16006XDDCR
LMR16006XDDCT
LMR16006XDDCT
LMR16006YDDCR
LMR16006YDDCR
LMR16006YDDCT
LMR16006YDDCT
Control ModeCurrent ModeCurrent ModeCurrent ModeCurrent Mode
Duty Cycle(Max), %97979797
Iout(Max), A0.60.60.60.6
Iq(Typ), mA0.0280.0280.0280.028
Operating Temperature Range, C-40 to 125-40 to 125-40 to 125-40 to 125
Package GroupSOT-23-THINSOT-23-THINSOT-23-THINSOT-23-THIN
RatingCatalogCatalogCatalogCatalog
Regulated Outputs1111
Special FeaturesEnable,Light Load Efficiency,Pre-Bias Start-Up,UVLO AdjustableEnable,Light Load Efficiency,Pre-Bias Start-Up,UVLO AdjustableEnable,Light Load Efficiency,Pre-Bias Start-Up,UVLO AdjustableEnable,Light Load Efficiency,Pre-Bias Start-Up,UVLO Adjustable
Switching Frequency(Max), kHz2100210021002100
Switching Frequency(Min), kHz700700700700
TypeConverterConverterConverterConverter
Vin(Max), V60606060
Vin(Min), V4444
Vout(Max), V55555555
Vout(Min), V0.80.80.80.8

Plan ecológico

LMR16006XDDCRLMR16006XDDCTLMR16006YDDCRLMR16006YDDCT
RoHSObedienteObedienteObedienteObediente

Notas de aplicación

  • SIMPLE SWITCHER Regulators Take Over Automotive Applications (Rev. A)
    PDF, 72 Kb, Revisión: A, Archivo publicado: abr 23, 2013
    Power management applications, typically located on the front line of the automotive electronics system,can be subject to wide input operating voltage extremes resulting from load-dump and cold-crankingconditions. Careful selection of the power management electronics can provide added margin andprotection to the automotive electronics system. The simplest design is provided by a power manage
  • Cap Drop Offline Supply for E-Meters
    PDF, 291 Kb, Archivo publicado: jun 16, 2015
    This design idea provides a simple non-isolated AC/DC power supply for low power applications such assmart grid E-meter applications. The design uses a "capacitive-dropper" front-end combined with aLM46000 SIMPLE SWITCHERВ® buck regulator from Texas Instruments. The circuit provides 3.3 V at aminimum of 50 mA from a line supply of 90 VAC to 265 VAC. Theory of operation as well as designequa
  • Cost-Effective Transformerless Offline Supply for Light Load Applications (Rev. A)
    PDF, 295 Kb, Revisión: A, Archivo publicado: jun 16, 2015
    This design idea provides a simple non-isolated AC/DC power supply for low power applications. Thedesign uses a "capacitive-dropper" front-end combined with a LM46000 SIMPLE SWITCHERВ® buckregulator from Texas Instruments. The circuit provides 3.3 V at a minimum of 100 mA from a line supply of90 VAC to 265 VAC. Theory of operation as well as design equations and performance results are given.
  • AN-1533 Overvoltage Protection Circuit for Automotive Load Dump (Rev. B)
    PDF, 83 Kb, Revisión: B, Archivo publicado: mayo 6, 2013
    This application report discusses an over voltage protection circuit for automotive load dump.
  • Understanding and Applying Current-Mode Control Theory
    PDF, 409 Kb, Archivo publicado: agosto 19, 2007
  • AN-1997 Error Amplifier Limitations in High-Performance Regulator Applications (Rev. A)
    PDF, 153 Kb, Revisión: A, Archivo publicado: mayo 6, 2013
    The development of realistic predictions to assist the power supply engineer during the control loop design process is facilitated in this application report by appropriate small-signal and bode plot analysis, the validity of which is verified through simulation results.
  • AN-2020 Thermal Design By Insight, Not Hindsight (Rev. C)
    PDF, 568 Kb, Revisión: C, Archivo publicado: abr 23, 2013
    This application report provides an in-depth discussion of thermal design.
  • AN-1246 Stresses in Wide Input DC-DC Converters (Rev. C)
    PDF, 427 Kb, Revisión: C, Archivo publicado: abr 23, 2013
    This application note discusses stresses in wide input DC-DC converters.
  • Low EMI Layout Made SIMPLE With LM43600/1/2/3 and LM46000/1/2 (Rev. A)
    PDF, 512 Kb, Revisión: A, Archivo publicado: sept 12, 2014
    Printed Circuit Board (PCB) layout for Switched Mode Power Supplies (SMPS) is critical to achieve proper converter operation good thermal performance and excellent radiated EMI performance. Optimized board layout for low radiated EMI is made very simple by the package and pin arrangement of the SIMPLE SWITCHER Synchronous Buck Converter family LM4360x and LM4600x
  • AN-1197 Selecting Inductors for Buck Converters (Rev. B)
    PDF, 558 Kb, Revisión: B, Archivo publicado: abr 23, 2013
    This application report provides design information to help select an off-the-shelf inductor for anycontinuous-mode buck converter application.
  • AN-1566 Techniques for Thermal Analysis of Switching Power Supply Designs (Rev. A)
    PDF, 1.4 Mb, Revisión: A, Archivo publicado: abr 23, 2013
    This application note provides thermal power analysis techniques for analyzing the power IC.
  • AN-1149 Layout Guidelines for Switching Power Supplies (Rev. C)
    PDF, 82 Kb, Revisión: C, Archivo publicado: abr 23, 2013
    When designing a high frequency switching regulated power supply layout is very important. Using agood layout can solve many problems associated with these types of supplies. The problems due to a badlayout are often seen at high current levels and are usually more obvious at large input to output voltagedifferentials. Some of the main problems are loss of regulation at high output current
  • AN-1889 How to Measure the Loop Transfer Function of Power Supplies (Rev. A)
    PDF, 2.7 Mb, Revisión: A, Archivo publicado: abr 23, 2013
    This application report shows how to measure the critical points of a bode plot with only an audiogenerator (or simple signal generator) and an oscilloscope. The method is explained in an easy to followstep-by-step manner so that a power supply designer can start performing these measurements in a shortamount of time.
  • AN-643 EMI/RFI Board Design (Rev. B)
    PDF, 742 Kb, Revisión: B, Archivo publicado: mayo 3, 2004
    Application Note 643 EMI/RFI Board Design
  • AN-2155 Layout Tips for EMI Reduction in DC/ DC Converters (Rev. A)
    PDF, 3.6 Mb, Revisión: A, Archivo publicado: abr 23, 2013
    This application note will explore how the layout of your DC/DC power supply can significantly affect theamount of EMI that it produces. It will discuss several variations of a layout analyze the results andprovide answers to some common EMI questions such whether or not to use a shielded inductor.
  • AN-1520 A Guide to Board Layout for Best Thermal Resistance for Exposed Packages (Rev. B)
    PDF, 9.2 Mb, Revisión: B, Archivo publicado: abr 23, 2013
    This thermal application report provides guidelines for the optimal board layout to achieve the best thermalresistance for exposed packages. The thermal resistance between junction-to-ambient (ОёJA) is highlydependent on the PCB (Printed Circuit Board) design factors. This becomes more critical for packageshaving very low thermal resistance between junction-to-case such as exposed pad TSSOP
  • AN-1229 SIMPLE SWITCHER PCB Layout Guidelines (Rev. C)
    PDF, 374 Kb, Revisión: C, Archivo publicado: abr 23, 2013
    This application report provides SIMPLE SWITCHER™ PCB layout guidelines.
  • AN-2162 Simple Success With Conducted EMI From DC-DC Converters (Rev. C)
    PDF, 2.5 Mb, Revisión: C, Archivo publicado: abr 24, 2013
    Electromagnetic Interference (EMI) is an unwanted effect between two electrical systems as a result ofeither electromagnetic radiation or electromagnetic conduction. EMI is the major adverse effect caused bythe application of switch-mode power supplies (SMPS). In switching power supplies EMI noise isunavoidable due to the switching actions of the semiconductor devices and resulting disconti
  • Semiconductor and IC Package Thermal Metrics (Rev. C)
    PDF, 201 Kb, Revisión: C, Archivo publicado: abr 19, 2016
  • Input and Output Capacitor Selection
    PDF, 219 Kb, Archivo publicado: sept 19, 2005

Linea modelo

Clasificación del fabricante

  • Semiconductors> Power Management> Non-isolated DC/DC Switching Regulator> Step-Down (Buck)> Buck Converter (Integrated Switch)