Datasheet Texas Instruments TLC2654IPE4 — Ficha de datos
| Fabricante | Texas Instruments |
| Serie | TLC2654 |
| Numero de parte | TLC2654IPE4 |
Amplificador operacional estabilizado por chopper de bajo ruido 8-PDIP -40 a 85
Hojas de datos
Advanced LinCMOS Low-Noise Chopper Stabilized Operational Amplifiers datasheet
PDF, 1.2 Mb, Revisión: G, Archivo publicado: abr 25, 2001
Extracto del documento
Precios
Estado
| Estado del ciclo de vida | Activo (Recomendado para nuevos diseños) |
| Disponibilidad de muestra del fabricante | No |
Embalaje
| Pin | 8 |
| Package Type | P |
| Industry STD Term | PDIP |
| JEDEC Code | R-PDIP-T |
| Package QTY | 50 |
| Carrier | TUBE |
| Device Marking | TLC2654IP |
| Width (mm) | 6.35 |
| Length (mm) | 9.81 |
| Thickness (mm) | 3.9 |
| Pitch (mm) | 2.54 |
| Max Height (mm) | 5.08 |
| Mechanical Data | Descargar |
Paramétricos
| Additional Features | Zero Drift |
| Architecture | CMOS |
| CMRR(Min) | 105 dB |
| CMRR(Typ) | 125 dB |
| GBW(Typ) | 1.9 MHz |
| Input Bias Current(Max) | 60 pA |
| Iq per channel(Max) | 2.4 mA |
| Iq per channel(Typ) | 1.5 mA |
| Number of Channels | 1 |
| Offset Drift(Typ) | 0.01 uV/C |
| Operating Temperature Range | -40 to 85,0 to 70 C |
| Output Current(Typ) | 3 mA |
| Package Group | PDIP |
| Package Size: mm2:W x L | See datasheet (PDIP) PKG |
| Rail-to-Rail | In to V-,Out |
| Rating | Catalog |
| Slew Rate(Typ) | 2.8 V/us |
| Total Supply Voltage(Max) | 16 +5V=5, +/-5V=10 |
| Total Supply Voltage(Min) | 4.6 +5V=5, +/-5V=10 |
| Vn at 1kHz(Typ) | 23 nV/rtHz |
| Vos (Offset Voltage @ 25C)(Max) | 0.02 mV |
Plan ecológico
| RoHS | Obediente |
| Pb gratis | Sí |
Notas de aplicación
- DC Parameters: Input Offset VoltagePDF, 295 Kb, Archivo publicado: marzo 27, 2001
The input offset voltage, VIO, is a common dc parameter in operational amplifier (op amp) specifications. This report aims to familiarize the engineer by discussing the basics and modern aspects of VIO by providing a definition and a detailed explaination of causes of VIO for BJT, BiFET, and CMOS devices. Discussion centers around measurement techniques, data sheet specifications, and the effect o - Choosing an ADC and Op Amp for Minimum OffsetPDF, 72 Kb, Archivo publicado: oct 28, 1999
Designing a mixed-signal circuit containing analog and digital components can be a challenge to the development engineer. Requirements such as a low single-polarity supply voltage and a high degree of precision may conflict, and make the choice of components and the best circuit design difficult. This report discusses problems that arise in using operational amplifiers (op amps) for signal conditi
Linea modelo
Serie: TLC2654 (14)
Clasificación del fabricante
- Semiconductors > Amplifiers > Operational Amplifiers (Op Amps) > Precision Op Amps