Datasheet LTC1250 (Analog Devices)

FabricanteAnalog Devices
DescripciónVery Low Noise Zero-Drift Bridge Amplifier
Páginas / Página12 / 1 — FEATURES. DESCRIPTIO. APPLICATIO S. TYPICAL APPLICATIO. Differential …
Formato / tamaño de archivoPDF / 184 Kb
Idioma del documentoInglés

FEATURES. DESCRIPTIO. APPLICATIO S. TYPICAL APPLICATIO. Differential Bridge Amplifier. Input Referred Noise 0.1Hz to 10Hz

Datasheet LTC1250 Analog Devices

Línea de modelo para esta hoja de datos

Versión de texto del documento

LTC1250 Very Low Noise Zero-Drift Bridge Amplifier
U FEATURES DESCRIPTIO
■ Very Low Noise: 0.75µVP-P Typ, 0.1Hz to 10Hz The LTC®1250 is a high performance, very low noise zero- ■ DC to 1Hz Noise Lower Than OP-07 drift operational amplifier. The LTC1250’s combination of ■ Full Output Swing into 1k Load low front-end noise and DC precision makes it ideal for use ■ Offset Voltage: 10µV Max with low impedance bridge transducers. The LTC1250 ■ Offset Voltage Drift: 50nV/°C Max features typical input noise of 0.75µVP-P from 0.1Hz to ■ Common Mode Rejection Ratio: 110dB Min 10Hz, and 0.2µVP-P from 0.1Hz to 1Hz. The LTC1250 has ■ Power Supply Rejection Ratio: 115dB Min DC to 1Hz noise of 0.35µVP-P, surpassing that of low noise ■ No External Components Required bipolar parts including the OP-07, OP-77, and LT1012. ■ Pin Compatible with Standard 8-Pin Op Amps The LTC1250 uses the industry-standard single op amp ■ Available in Standard 8-Pin Plastic DIP pinout, and requires no external components or nulling and 8-Pin SO Packages signals, allowing it to be a plug-in replacement for bipolar op amps.
U APPLICATIO S
The LTC1250 incorporates an improved output stage capable of driving 4.3V into a 1k load with a single 5V ■ Electronic Scales supply; it will swing ±4.9V into 5k with ±5V supplies. The ■ Strain Gauge Amplifiers input common mode range includes ground with single ■ Thermocouple Amplifiers power supply voltages above 12V. Supply current is 3mA ■ High Resolution Data Acquisition with a ±5V supply, and overload recovery times from ■ Low Noise Transducers positive and negative saturation are 0.5ms and 1.5ms, ■ Instrumentation Amplifiers respectively. The internal nulling clock is set at 5kHz for , LTC and LT are registered trademarks of Linear Technology Corporation. All other optimum low frequency noise and offset drift; no external trademarks are the property of their respective owners. Protected by U.S. Patents connections are necessary. including 4933642. The LTC1250 is available in a standard 8-pin plastic DIP and 8-pin SO packages.
U TYPICAL APPLICATIO Differential Bridge Amplifier Input Referred Noise 0.1Hz to 10Hz
5V 5V 2 VS = ±5V 50Ω AV = 10k 1000pF GAIN 0.1µF TRIM 1 18.2k V 0 350 µ Ω 2 7 STRAIN – GAUGE 6 LTC1250 AV = 100 3 –1 + 4 1000pF 18.2k –2 0 2 4 6 8 10 –5V –5V 1250 TA01 TIME (s) LT1250 TA02 1250fb 1