Datasheet LT6550, LT6551 (Analog Devices) - 3

FabricanteAnalog Devices
Descripción3.3V Triple and Quad Video Amplifiers
Páginas / Página16 / 3 — 3.3V ELECTRICAL CHARACTERISTICS The. denotes the specifications which …
Formato / tamaño de archivoPDF / 311 Kb
Idioma del documentoInglés

3.3V ELECTRICAL CHARACTERISTICS The. denotes the specifications which apply over the specified

3.3V ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the specified

Línea de modelo para esta hoja de datos

Versión de texto del documento

LT6550/LT6551
3.3V ELECTRICAL CHARACTERISTICS The

denotes the specifications which apply over the specified temperature range, otherwise specifications are at TA = 25
°
C. VCC = 3.3V, VGND = 0V; VIN = 0.75V LT6550 (Pins 1,2,3); LT6551 (Pins 1,2,3,4). VEE = 0V LT6550 (Pin 5), unless otherwise noted. PARAMETER CONDITIONS MIN TYP MAX UNITS
Output Voltage Swing High VIN = 1.75V No Load ● 3.0 3.2 V RL = 150Ω ● 2.5 2.9 V RL = 75Ω 2.0 2.5 V PSRR VCC = 3V to 10V, VIN = 0.5V ● 40 48 dB Minimum Supply Voltage (Note 6) ● 3 V Output Short-Circuit Current VIN = 1V, VOUT = 0V 35 50 mA ● 25 mA Supply Current per Amplifier (Note 7) 8.5 10 mA ● 11 mA Slew Rate (Note 8) RL = 150Ω, VOUT = 0.5V to 2.5V 140 250 V/µs Measured from 1V to 2V ● 115 V/µs Small Signal –3dB Bandwidth RL = 150Ω 90 MHz Gain Flatness Less than 0.25dB 30 MHz Gain Matching Any One Channel to Any Other Channel 0.15 dB Settling Time to 3% RL = 150Ω, VOUT = 1V to 2.5V 20 ns Settling Time to 1% RL = 150Ω, VOUT = 1V to 2.5V 30 ns % Overshoot VOUT = 1V to 2.5V, RL = 150Ω 5 % Differential Gain RL = 150Ω, Black Level = 0.6V at Device Output 0.09 % Differential Phase RL = 150Ω, Black Level = 0.6V at Device Output 0.09 Deg Channel Separation Measured at 10MHz 60 dB
5V ELECTRICAL CHARACTERISTICS The

denotes the specifications which apply over the specified temperature range, otherwise specifications are at TA = 25
°
C. VCC = 5V, VGND = 0V; VIN = 1.25V LT6550 (Pins 1,2,3); LT6551 (Pins 1,2,3,4). VEE = 0V LT6550 (Pin 5), unless otherwise noted. PARAMETER CONDITIONS MIN TYP MAX UNITS
Output Accuracy No Load, VOUT Ideal = 2.5V ● 30 70 mV Output Voltage Matching Between Any Two Outputs ● 40 90 mV Input Current ● 15 65 µA Input Impedance, ∆VIN/∆IIN VIN = 0V to 2V ● 100 300 kΩ Input Noise Voltage Density f = 100kHz (Note 10) 12 nV/√Hz Input Noise Current Density f = 100kHz (Note 10) 8 pA/√Hz Voltage Gain (Note 5) 0.25V ≤ VIN ≤ 1.75V No Load ● 1.9 2.1 V/V RL = 150Ω ● 1.9 2.1 V/V RL = 75Ω, 0.25V ≤ VIN ≤ 1.25V, 0°C ≤ TA ≤ 70°C (Only) ● 1.85 2.15 V/V Output Voltage Swing Low VIN = – 0.1V No Load ● 10 30 mV ISINK = 5mA ● 60 150 mV ISINK = 10mA ● 90 200 mV Output Voltage Swing High VIN = 2.6V No Load ● 4.6 4.8 V RL = 150Ω ● 3.5 4.1 V RL = 75Ω, 0°C ≤ TA ≤ 70°C (Only) ● 2.5 3.2 V 65501fa 3