Datasheet LTC7804 (Analog Devices) - 5

FabricanteAnalog Devices
DescripciónLow IQ Synchronous Boost Controller
Páginas / Página34 / 5 — ELECTRICAL CHARACTERISTICS. The. denotes the specifications which apply …
Formato / tamaño de archivoPDF / 1.5 Mb
Idioma del documentoInglés

ELECTRICAL CHARACTERISTICS. The. denotes the specifications which apply over the specified operating

ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the specified operating

Línea de modelo para esta hoja de datos

Versión de texto del documento

LTC7804
ELECTRICAL CHARACTERISTICS The
l
denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are for TA = 25°C, VBIAS = 12V, RUN = 12V, EXTVCC = 0V, unless otherwise noted. (Note 2) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Input Supply
VBIAS Bias Input Supply Operating Range 4.5 40 V VIN Boost Converter Input Supply Operating Range VBIAS ≥ 4.5V 1 40 V VOUT Output Voltage Operating Range 40 V
Controller Operation
VFB Regulated Feedback Voltage (Note 3) VBIAS = 4.5V to 40V, ITH Voltage = 0.6V to 1.2V l 1.188 1.2 1.212 V Feedback Current (Note 3) ±5 ±50 nA Feedback Overvoltage Protection Threshold Measured at VFB Relative to Regulated VFB 7 10 13 % gm Transconductance Amplifier gm (Note 3) ITH = 1.2V, Sink/Source = 5μA 2 mmho VSENSE(MAX) Maximum Current Sense Threshold VFB = 1.1V, VSENSE+ = 12V l 45 50 55 mV ISENSE+ ISENSE+ Pin Current VSENSE+ < 2.9V 2 μA 3.2 ≤ VSENSE+ ≤ INTVCC −0.5V 30 μA VSENSE+ > INTVCC + 0.5V 650 μA ISENSE− SENSE− Pin Current VSENSE− = 12V ±1 μA Soft-Start Charge Current VSS = 0V 10 12.5 15 µA RUN Pin ON Threshold VRUN Rising l 1.15 1.2 1.25 V RUN Pin Hysteresis 100 mV
DC Supply Current (Note 4)
IQ VBIAS Shutdown Current RUN = 0V 1.2 μA VBIAS Sleep Mode Current VSENSE+ < 2.9V, EXTVCC = 0V 14 28 μA VSENSE+ ≥ 3.2V VBIAS Current, EXTVCC = 0V 5 μA VBIAS Current, EXTVCC ≥ 4.8V 1 μA EXTVCC Current, EXTVCC ≥ 4.8V 4 μA SENSE+ Current 9 μA Pulse-Skipping or Forced Continuous Mode VFB = 1.25V 2 mA VBIAS or EXTVCC Current
Gate Drivers
TG or BG On-Resistance Pull-Up 3.0 Ω Pull-Down 1.5 Ω TG or BG Transition Time (Note 5) Rise Time CLOAD = 3300pF 25 ns Fall Time CLOAD = 3300pF 15 ns TG Off to BG On Delay CLOAD = 3300pF Each Driver Bottom Switch-On Delay Time 15 ns BG Off to TG On Delay CLOAD = 3300pF Each Driver Synchronous Switch-On Delay Time 15 ns tON(MIN) BG Minimum On-Time (Note 6) 80 ns Maximum Duty Factor for TG Overvoltage 100 % Maximum Duty Factor for BG VFREQ = 0V 93 % Rev. 0 For more information www.analog.com 5 Document Outline Features Applications Typical Application Description Absolute Maximum Ratings Pin Configuration Order Information Electrical Characteristics Typical Performance Characteristics Pin Functions Block Diagram Operation Main Control Loop INTVCC/EXTVCC Power Boost Supply and Dropout (BOOST and SW Pins) Shutdown and Start-Up (RUN, SS Pins) Light Load Current Operation: Burst Mode Operation, Pulse-Skipping or Forced Continuous Mode (MODE Pin) Frequency Selection, Spread Spectrum and Phase-Locked-Loop (FREQ and PLLIN/SPREAD Pins) Operation When VIN > VOUT Operation at Low Input Voltage BOOST Supply Refresh and Internal Charge Pump Applications Information SENSE+ and SENSE– Pins Low Value Resistor Current Sensing Inductor DCR Sensing Inductor Value Calculation Inductor Core Selection Power MOSFET Selection CIN and COUT Selection Setting Output Voltage RUN Pin Soft-Start (SS Pin) INTVCC Regulators Topside MOSFET Driver Supply (CB, DB) Phase-Locked Loop and Frequency Synchronization Setting the Operating Frequency Selecting the Light-Load Operating Mode Minimum On-Time Considerations Fault Conditions: Overtemperature Protection Efficiency Considerations Checking Transient Response Design Example PC Board Layout Checklist PC Board Layout Debugging Package Description Typical Application Related Parts