Datasheet TLP2372 (Toshiba) - 3

FabricanteToshiba
DescripciónPhotocouplers Infrared LED & Photo IC
Páginas / Página17 / 3 — TLP2372. 7. Absolute. Maximum. Ratings. (Note). (Unless. otherwise. …
Formato / tamaño de archivoPDF / 645 Kb
Idioma del documentoInglés

TLP2372. 7. Absolute. Maximum. Ratings. (Note). (Unless. otherwise. specified,. Ta. =. 25. ). Characteristics. Symbol. Note. Rating. Unit. LED. Input. forward

TLP2372 7 Absolute Maximum Ratings (Note) (Unless otherwise specified, Ta = 25 ) Characteristics Symbol Note Rating Unit LED Input forward

Línea de modelo para esta hoja de datos

Versión de texto del documento

TLP2372 7. Absolute Maximum Ratings (Note) (Unless otherwise specified, Ta = 25 ) Characteristics Symbol Note Rating Unit LED Input forward current IF 8 mA Input forward current derating (Ta ≥ 110 ) ∆IF/∆Ta -0.32 mA/ Input forward current (pulsed) IFP (Note 1) 16 mA Input forward current derating (Ta ≥ 110 ) ∆IFP/∆Ta -0.64 mA/ (pulsed) Peak transient input forward IFPT (Note 2) 1 A current Peak transient input forward (Ta ≥ 110 ) ∆IFPT/∆Ta -40 mA/ current derating Input reverse voltage VR 5 V Input power dissipation PD 20 mW Input power dissipation (Ta ≥ 110 ) ∆PD/∆Ta -0.8 mW/ derating Detector Output current IO 8 mA Output voltage VO -0.5 to VDD + 0.5 V Supply voltage VDD -0.5 to 6 V Output power dissipation PO 20 mW Output power dissipation (Ta ≥ 110 ) ∆PO/∆Ta -0.8 mW/ derating Common Operating temperature Topr -40 to 125 Storage temperature Tstg -55 to 125 Lead soldering temperature (10 s) Tsol 260 Isolation voltage (AC, 60 s, R.H. ≤ 60 %) BVS (Note 3) 3750 Vrms Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: Pulse width (PW) ≤ 1 ms, duty = 50 % Note 2: Pulse width (PW) ≤ 1 µs, 300 pps Note 3: This device is considered as a two-terminal device: Pins 1 and 3 are shorted together, and pins 4, 5 and 6 are shorted together. 8. Recommended Operating Conditions (Note) Characteristics Symbol Note Min Typ. Max Unit Input on-state current IF(ON) 2  6 mA Input off-state voltage VF(OFF) 0  0.8 V Rise time of IF tr(IF) (Note 1) 5 n  60 s Fall time of IF tf(IF) (Note 2) 5 n  60 s Supply voltage VDD (Note 3) 2.2 2.5 / 3.3 / 5 5.5 V Operating temperature Topr (Note 3) -40  125 Note: The recommended operating conditions are given as a design guide necessary to obtain the intended performance of the device. Each parameter is an independent value. When creating a system design using this device, the electrical characteristics specified in this data sheet should also be considered. Note: A ceramic capacitor (0.1 µF) should be connected between pin 6 and pin 4 to stabilize the operation of a high- gain linear amplifier. Otherwise, this photocoupler may not switch properly. The bypass capacitor should be placed within 1 cm of each pin. Note 1: The rise time of input forward current which takes for linear increase from 0 mA to 2 mA. Note 2: The fall time of input forward current which takes for linear decrease from 2 mA to 0 mA. Note 3: Denotes the operating range, not the recommended operating condition. ©2020 3 2020-03-31 Toshiba Electronic Devices & Storage Corporation Rev.2.0