Datasheet USB4125, USB4130, USB4135 (GCT) - 4
| Fabricante | GCT |
| Descripción | Type C USB Charging Connector |
| Páginas / Página | 10 / 4 — Part. Rev. Date. Number Product. Page. Description Doc. Prepared. … |
| Formato / tamaño de archivo | PDF / 395 Kb |
| Idioma del documento | Inglés |
Part. Rev. Date. Number Product. Page. Description Doc. Prepared. Checked. Approved. Number. www.gct.co
Línea de modelo para esta hoja de datos
Versión de texto del documento
PRODUCT SPECIFICATION
Part
USB4125, USB4130, USB4135
Rev
A3
Date
20/12/24
Number Product
USB Type C Receptacle, 6 contacts, For Power Charging only
Page
4
Description Doc
USB Type C
Prepared
YR
Checked
CC
Approved
PH
Number
6.2 Mechanical Performance Test No Item Test Condition Requirement Mating force: within 5N to 20N (initial). Un-Mating force: Mating/Un-mating Mate/Un-mated at a speed of 12.5mm/min. 6.2.1 within 8N to 20N up Force In accordance with EIA-364-13. to 30cycles, within 6N to 20N after 20,000cycles Un-Mating force: 20,000 cycles at a within 6N to 20N cycle rate 500± 50 per hour. Contact resistance: Durability In accordance with EIA-364-09. 50mΩ max (Replace the plug after 10K cycles) Dielectric Strength: 6.2.2 no breakdown 50 cycles at a Durability cycle rate 500± 50 per hour - (Preconditioning) In accordance with EIA-364-09. No evidence of EIA 364-28 Test Condition VII, Test Letter D physical damage and 15 minutes in each of 3 mutually perpendicular no discontinuity directions. Both mating halves should be rigidly 6.2.3 Vibration longer than 1 fixed so as not to contribute to the relative motion of microsecond. one contact against another. The method of Contact resistance: fixturing should be detailed in the test report 50mΩ max. No evidence of physical damage and Shall be tested for continuity under stress using 6.2.4 4-Axis Continuity no discontinuity a test fixture longer than 1 microsecond.
www.gct.co
Part
USB4125, USB4130, USB4135
Rev
A3
Date
20/12/24
Number Product
USB Type C Receptacle, 6 contacts, For Power Charging only
Page
4
Description Doc
USB Type C
Prepared
YR
Checked
CC
Approved
PH
Number
6.2 Mechanical Performance Test No Item Test Condition Requirement Mating force: within 5N to 20N (initial). Un-Mating force: Mating/Un-mating Mate/Un-mated at a speed of 12.5mm/min. 6.2.1 within 8N to 20N up Force In accordance with EIA-364-13. to 30cycles, within 6N to 20N after 20,000cycles Un-Mating force: 20,000 cycles at a within 6N to 20N cycle rate 500± 50 per hour. Contact resistance: Durability In accordance with EIA-364-09. 50mΩ max (Replace the plug after 10K cycles) Dielectric Strength: 6.2.2 no breakdown 50 cycles at a Durability cycle rate 500± 50 per hour - (Preconditioning) In accordance with EIA-364-09. No evidence of EIA 364-28 Test Condition VII, Test Letter D physical damage and 15 minutes in each of 3 mutually perpendicular no discontinuity directions. Both mating halves should be rigidly 6.2.3 Vibration longer than 1 fixed so as not to contribute to the relative motion of microsecond. one contact against another. The method of Contact resistance: fixturing should be detailed in the test report 50mΩ max. No evidence of physical damage and Shall be tested for continuity under stress using 6.2.4 4-Axis Continuity no discontinuity a test fixture longer than 1 microsecond.
www.gct.co