Datasheet LTC7804 (Analog Devices) - 3

FabricanteAnalog Devices
DescripciónLow IQ Synchronous Boost Controller
Páginas / Página34 / 3 — ABSOLUTE MAXIMUM RATINGS (Note 1). PIN CONFIGURATION
Formato / tamaño de archivoPDF / 1.5 Mb
Idioma del documentoInglés

ABSOLUTE MAXIMUM RATINGS (Note 1). PIN CONFIGURATION

ABSOLUTE MAXIMUM RATINGS (Note 1) PIN CONFIGURATION

Línea de modelo para esta hoja de datos

Versión de texto del documento

LTC7804
ABSOLUTE MAXIMUM RATINGS (Note 1)
ITH ... −0.3V to 2V Bias Input Supply Voltage (VBIAS) .. −0.3V to 40V SS, FREQ ... −0.3V to 6V BOOST ... −0.3V to 46V PLLIN/SPREAD, MODE, VFB ... −0.3V to 6V SW ... −5V to 40V BG, TG ... (Note 8) RUN ... −0.3V to 40V Operating Junction Temperature Range (Notes 2, 7) SENSE+, SENSE− ... −0.3V to 40V LTC7804E, LTC7804I ... −40°C to 125°C EXTVCC Voltage ... −0.3V to 30V LTC7804H ... −40°C to 150°C INTVCC, (BOOST-SW) .. −0.3V to 6V Storage Temperature Range .. −65°C to 150°C
PIN CONFIGURATION
TOP VIEW CC BOOST BG V BIAS EXTV TOP VIEW 16 15 14 13 SS 1 16 SW SENSE– 2 15 TG TG 1 12 INTVCC SENSE+ 3 14 BOOST SW 2 17 11 MODE V 4 FB 17 13 BG ITH 5 GND GND 12 V SS PLLIN/SPREAD BIAS 3 10 RUN 6 11 EXTVCC SENSE– 4 9 FREQ FREQ 7 10 INTVCC PLLIN/SPREAD 8 9 MODE 5 6 7 8 MSE PACKAGE + V FB ITH 16-LEAD PLASTIC MSOP RUN TJMAX = 125°C, θJA = 40°C/W, θJC = 10°C/W SENSE EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB UD PACKAGE 16-LEAD (3mm × 3mm) PLASTIC QFN TJMAX = 125°C, θJA = 68°C/W, θJC = 4.2°C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB Rev. 0 For more information www.analog.com 3 Document Outline Features Applications Typical Application Description Absolute Maximum Ratings Pin Configuration Order Information Electrical Characteristics Typical Performance Characteristics Pin Functions Block Diagram Operation Main Control Loop INTVCC/EXTVCC Power Boost Supply and Dropout (BOOST and SW Pins) Shutdown and Start-Up (RUN, SS Pins) Light Load Current Operation: Burst Mode Operation, Pulse-Skipping or Forced Continuous Mode (MODE Pin) Frequency Selection, Spread Spectrum and Phase-Locked-Loop (FREQ and PLLIN/SPREAD Pins) Operation When VIN > VOUT Operation at Low Input Voltage BOOST Supply Refresh and Internal Charge Pump Applications Information SENSE+ and SENSE– Pins Low Value Resistor Current Sensing Inductor DCR Sensing Inductor Value Calculation Inductor Core Selection Power MOSFET Selection CIN and COUT Selection Setting Output Voltage RUN Pin Soft-Start (SS Pin) INTVCC Regulators Topside MOSFET Driver Supply (CB, DB) Phase-Locked Loop and Frequency Synchronization Setting the Operating Frequency Selecting the Light-Load Operating Mode Minimum On-Time Considerations Fault Conditions: Overtemperature Protection Efficiency Considerations Checking Transient Response Design Example PC Board Layout Checklist PC Board Layout Debugging Package Description Typical Application Related Parts